JC-CT02 Oil Filled Sensor

Parameters	≤34KPa			≥100KPa
	MIN	TYP	MAX	MIN	TYP	MAX
Span mV	50	100	150	75	100	150
Zero pressure output mV	-2	0	2	-1	0	1
Non-linearity  %Span	7KPa:  -0.30 to 0.30			-0.1		0.1
	34KPa: -0.20 to 0.20			-0.2		0.2
Hysteresis %Span	-0.1	±0.02	0.1	-0.05	±0.02	0.05
Repeatability %Span		±0.02			±0.02
Input Resistance KΩ	2	3.5	6.5	2	3.5	5.8
Output Resistance KΩ	4		7	4		6
Temperature Error-Span  %Span	-1		1	-0.75		0.75
Temperature Error-Offset %Span	-1		1	15psi: -0.75 to 0.75; >15psi: -0.50 to 0.50
Thermal Hysteresis-Span %Span	-0.25	±0.05	0.25	-0.25	±0.05	0.25
Thermal Hysteresis-Offset %Span	-0.25	±0.05	0.25	-0.25	±0.05	0.25
Long-term stability-Span %/year		±0.1			±0.1
Long-term stability-zero % /year		±0.25			±0.25
Supply Current mA	0.5	1.5	2	0.5	1.5	2
Output Load Resistance MΩ	5			5
Insulation Resistance MΩ (50VDC)	50			50
Output Noise uV p-p (10Hz to 1KHz)		1			1
Response Time ms (10% to 90%)		0.1			0.1
Pressure Overload Rated	7kpa: 10X max; 34kpa: 3X max					3X
Pressure Burst Rated	7kpa: 12X max; 34kpa: 4X max					4X
Compensated temperature °C	7kpa: 0 to 50; 34kpa: 0 to 70			-20		85
Operating temperature °C	-20		70			125
Storage Temperature °C	-50		125			125
Media – Pressure Port	Liquids and Gases compatible with 304/316L Stainless Steel
Media – Reference Port	Compatible with Silicon, Pyrex, Gold, Fluorosilicone Rubber, and 304/316L Stainless Steel

JC-CT02 Pressure sensor
Model	Description
JC-CT02	Diameter 19mm O Ring mounting
	Code	Power Supply
	C	Constant Current
	V	Constant Voltage
		Code	Pressure Range	Gauge	Absolute
		7K	0~7KPa	*
		30K	0~30KPa	*	*
		100K	0~100KPa	*	*
		200K	0~200KPa	*	*
		350k	0~350KPa	*	*
		700K	0~700KPa	*	*
		2M	0~2MPa	*	*
		3.5M	0~3.5MPa	*	*
		XX	Customized
			Code	Pressure type
			G	Vent Gauge Pressure(W/O vent tube as default）
			A	Absolute Pressure
				Code	Electrical Connection
				1	Connect Pins
				2	Ribbon Cable (90mm as default)
				X	Special

Note:
1. Least squares fitting straight line
2. Compared with the output of 25 °C in the compensation temperature range
3. Can be used for down-range, and the amplitude is controlled within ±50%FS.
4. The maximum pressure of the system should be less than the overload protection limit of the sensor, otherwise it will affect the service life of  the product and damage the product.
5. The commonly used compensation method for products is 1.5mA constant current compensation.
6. Do not force to pull the pins or the leads of sensitive components.
7. Protect the isolation diaphragm at the front end of the pressure sensitive component to prevent the impact of the pressure sensitive component from damaging the sensitive component.
8. If you have special requirements on product performance parameters and functions, please contact us.