We use cookies to improve your online experience. By continuing browsing this website, we assume you agree our use of cookies.
Your position: Home / Pressure Sensor / Ceramic Pressure Sensor

JC-CS01 Ceramic Pressure Sensor

Ø18mm Ceramic piezoresistance
Compensation Temp. -10~70℃
Pressure Range: 2bar, 5bar, 10bar, 20bar, 30bar, 50bar, 100bar, 200bar
  • Range:
(8997 available)
Shipping Cost:
Estimated Delivery Time:
Please select the country you want to ship from
Please select the information you wantX
  • Description
  • Dimensions(mm)
  • Technical Parameters
  • Ordering Information
  • Reviews


JC-CS01 monolithic pressure sensors are made with a ceramic cell and work following the piezoresistive principle. The Wheatstone bridge is screen printed directly on one side of the ceramic diaphragm by means of Thick Film technology. The diaphragm’s opposite side can be exposed directly to the medium to be measured. Because of the Al2O3 ceramic excellent chemical resistance (aggressive gases, most of solvents and acids, etc.), no additional protection is normally required. Thanks to the reinforced outer area (monolithic structure), the sensor can be mounted directly in a plastic or metallic case by using O-ring. 
JC-CS01 sensors are designed in such a way so that temperature changes and pressure overloads do not cause loss in reliability. JC-CS01 sensors ensure optimal linearity across the entire range of measurement and minimize effects of hysteresis. 


* Low cost OEM    
* Wide operable temperature range -40-135 ℃   
* Compatible with corrosive media     
* Small profile and easily to be welded    
* Typical output:3mV/V


* Pneumatic Equipment
* Hydraulic Equipment
* Medical Equipment
* Air Compressors
* Refrigeration Systems
* Battery-powered Equipment

Packing Picture

1:+ Excitation voltage
2:- output
3:- Excitation voltage
4:+ output
Note: Other electrical connections are available on request
Pressure range 0~2bar…0~600bar(G)
Dimension φ18×6.35mm
Power supply 30V DC, Max.
Bridge impedance 11KΩ±30%
Zero drift ≤±0.2mV/V
Insulation resistance >2kv
Zero long-term stability @20°C ±0.2%FSO,typical.
Direct contact with liquid material 96%AL2O3
Operating temperature -40~135℃
Sored temperature -50~150℃
Temperature drift(zero+sensitivity) ≤±0.03%FS/℃(2bar~200bar);≤±0.04%FS/℃400bar & 600bar)
Accuracy(non-linear+ Hysteresis) ≤±0.3%FS
Repeatability ≤±0.1%FS
Type Pressure Range(bar) Break Pressure(*) (bar) Full Scale output (mV/V)
JC-CS01-2 0…2 4 2.0/4.0
JC-CS01-5 0…5 12.5 2.0/4.0
JC-CS01-10 0…10 25 2.0/4.0
JC-CS01-20 0…20 50 2.4/3.6
JC-CS01-30 0…30 80 1.8/3.0
JC-CS01-40 0…40 110 2.4/3.6
JC-CS01-50 0…50 125 2.4/3.6
JC-CS01-80 0…80 180 2.4/3.6
JC-CS01-100 0…100 200 2.0/3.0
JC-CS01-200 0…200 400 2.0/3.0
JC-CS01-400 0…400 600 1.8/3.0
JC-CS01-600 0…600 800 1.6/2.5

1. (*): Except for hydroxy acid
Break Pressure is calibrated at normal temperature, please contact us under high or low temperature.
2. Electric connection: Pin or leads
3. Compared with the output of 25 °C in the compensation temperature range
4. Can be used for down-range, and the amplitude is controlled within ±50%FS.
5. The maximum pressure of the system should be less than the overload protection limit of the sensor, otherwise it will affect the service life of the product and damage the product.
6. The commonly used compensation method for products is 1.5mA constant current compensation.
7. Do not force to pull the pins or the leads of sensitive components.
8. Protect the isolation diaphragm at the front end of the pressure sensitive component to prevent the impact of the pressure sensitive component from damaging the sensitive component.
9. If you have special requirements on product performance parameters and functions, please contact us.
Average rating:
Share your thoughts with other customers
Write a review
Product reviews can be carried out after the member login, please click here to login